Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Roofing: The Fort Worth Owner’s Guide
We stock and install CGI-compatible roofing components across Fort Worth, with most installed jobs running $400 to $1,800 for repairs and $8,000 to $20,000 for full roof replacement depending on material, pitch, and square footage. If you’ve got a CGI roof that’s leaking, lifting, or showing rust at the fasteners, we can usually match the part same week. Most Fort Worth homeowners discover the issue after a spring hailstorm or a hard summer wind event: a shingle edges up, a fastener backs out, or a panel shows a crease that was not there before.
What you are reading now is written for the owner who already knows they have a CGI product and wants the failing part matched, priced, and handled without a twelve-call scavenger hunt. We are an independent service provider, not a CGI dealer or factory arm. That independence matters: it means we can tell you honestly whether the original part or a quality aftermarket equivalent is the better spend for a roof that will face another Texas July.
Which CGI Models This Applies To
CGI roofing runs across several product lines, and the part matching is where most callers get stuck. The most common in Fort Worth are the stone-coated steel shingle profiles (think the heavier, textured panels often spec’d on homes in neighborhoods like Mistletoe Heights or Crestline) and the standing-seam panels showing up on newer builds closer to Alliance. Each line uses a different fastener type, a different panel gauge, and a different ridge cap profile. If you have the original packaging or a leftover bundle in the garage, look for the manufacturer stamp on the back of a full shingle: it will list the series, the color code, and usually the gauge. If you only have the damaged piece, measure the exposed profile width and the nail strip spacing before you call. That single measurement saves us both a drive.
When we match CGI parts in Fort Worth, we give you the OEM versus aftermarket decision in plain terms. OEM CGI components carry the manufacturer’s warranty and keep the roof’s full wind-rating intact; they also cost more and can take longer to source. A quality aftermarket equivalent, matched by gauge and profile, often installs identically and performs the same in our climate, but it will not carry the CGI brand warranty. We stock common aftermarket fasteners, closures, and ridge caps on the truck for the stone-coated steel lines, and we order OEM when the homeowner wants the factory chain intact. We also carry materials for KraftMaid, Cambria, and Silestone projects, so if you are doing interior work at the same time, we can coordinate the full scope.
Styles & brands we work with
Signs Your CGI Roofing Is Failing
- Rust streaking from fastener heads. In Fort Worth’s humidity cycle and hard rain, the neoprene washers under CGI fasteners degrade before the panel does. Water follows the fastener shaft down and leaves a rust thread on the metal below the head. By the time you see the streak, the seal is gone.
- Loose or lifted shingle edges after wind. The stone-coated steel profiles interlock, but a hard north Texas gust can press the laps open if the original installer over-torqued the fasteners. A raised edge is not cosmetic; it is a water entry point waiting for the next storm front.
- Granule loss in a single concentrated spot. stone-coated steel does not shed the way asphalt does, so if you see a patch of bare, glinting metal at a valley or a transition, that is mechanical wear from water moving fast. It almost always traces back to a bad closure or a missing cricket.
- Any crease, dent, or puncture after hail. CGI panels are tough, but a Fort Worth hailstorm the size of the one that hit the wedge between Benbrook and Wedgwood in 2023 will crease a panel at the thinnest point. Once the stone coat cracks along the crease line, moisture gets under the stone and the corrosion clock starts.
- Damp drywall or attic sheathing below a wall-to-roof transition. Most CGI failures in Fort Worth that we repair are not full-panel failures; they are transition failures. The wall flashing, the pipe boot, the ridge vent end cap. The roof looks fine from the curb. The wet spot in the guest room ceiling tells a different story.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Fort Worth, a targeted CGI part replacement runs $400 to $1,800 installed, and a full tear-off plus new metal roof runs $8,000 to $20,000 depending on the roof area, pitch, and whether we are reusing existing underlayment or laying new. The range moves on three things: how many panels or profiles require matching, whether the underlayment under the failed area has soaked through, and access. A standing-seam panel replacement on a two-story roof in the Cultural District will price differently than a stone-coated shingle swap on a single-story ranch in Stop Six.
What is included: the part cost, the labor, the disposal of the damaged material, new fasteners and closures, and a written line-item price before any work starts. We do not hand over an estimate and then find a surprise once the old panel comes off. The written price and the final invoice should read the same – if they don’t, that is on us to explain before we hand you a pen. Every repair carries our 365-Day Done Right Promise: if the fix does not hold, we make it right. The crew shows up in uniform, covers the floors in the house where we need to access the attic, and photographs the clean-up before we leave, because Graham Stein and our Fort Worth crew believe the condition we leave the driveway in is part of the job, not an add-on.
DIY or Call Us?
There is a safe version of self-help here, and then there is the version that puts you on a ladder with a drill in a wind gust. The safe version: check your gutters after a storm for granule piles, look for the rust streaks described above, and take photos of anything that looks lifted. Photos are genuinely useful. What we ask you not to do is get on the roof and start pulling fasteners. Steel panels are under tension at the laps, the surface gets slick with morning dew, and a Fort Worth roof pitch plus a metal surface is not the place to learn a new skill. Graham Stein learned this trade at Los Angeles Trade-Technical College and has spent decades doing construction across North Texas, and he will be the first to tell you that a roof is where he is most careful with his own crew, let alone a homeowner.
If the damage is a loose fastener you can reach from a ladder with both feet on the ground and no stretching, a hand-tightened replacement is reasonable. Anything beyond that, call us at (682) 708-9180. We will come look, write down what we find, and give you the price before any tool comes off the truck.
FAQs
A properly installed CGI roof in Fort Worth lasts 30 to 50 years, with the stone coating and the galvanized steel substrate both engineered for decades, but the fasteners and closures typically need attention every 12 to 20 years depending on shade, slope, and exposure. Call (682) 708-9180 and we can put eyes on the specific failing part before guessing at the remaining roof life.
A creased or rusted-through panel gets replaced, not patched; the stone coating cannot be re-adhered over a crease or a corrosion hole in a way that survives another Texas hail season. Small fastener leaks and closure gaps can often be repaired with a new fastener set and sealant, no panel swap needed. Call (682) 708-9180 and describe the damage; we will tell you over the phone which category yours falls into.
Most single-part CGI replacements in Fort Worth take one crew visit of three to six hours, from the first ladder touch to the photo of the clean-up. Full roof replacements run three to seven working days depending on weather and the roof’s geometry. We schedule noisy demo outside school-pickup hours when families are home, and we work around naptime where we can.
We stock common aftermarket fasteners, closures, ridge caps, and transition flashings for the CGI stone-coated steel lines on our Fort Worth trucks, and for OEM parts we order direct and typically install within one to two weeks. If you have the packaging or a stamp code, call (682) 708-9180 right now and we will tell you in two minutes whether the part is on the truck or needs to be ordered.
If your CGI roof is showing any of the signs above, or if you just want a second set of eyes before the next storm season, call (682) 708-9180. A live person answers, twenty-four hours a day, and we will schedule a free estimate at a time that works for your family. The quote is written, line by line, before you sign anything.
Written by Graham Stein, Owner, Elmstead Remodeling Fort Worth at Elmstead Remodeling Fort Worth, serving Fort Worth and nearby areas.
