Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Fence Installation: The Fort Worth Owner’s Guide
Mr-Glass fence installation in Fort Worth typically runs $3,500 to $9,000 for a full perimeter install, and we can usually start within two weeks of your written estimate. Most owners call us when a windstorm has snapped a post at the base or when a gate has sagged so badly it drags across the concrete. You’ll notice it first as a lean you can see from the street, or a gate that no longer latches without a shoulder behind it.
We’re an independent Fort Worth contractor, not affiliated with Mr-Glass directly. What that means for you: we can source Mr-Glass compatible fence components, install them to Fort Worth wind and soil conditions, and stand behind the work with our 365-Day Done Right Promise. If it’s not done right after the job is complete, we make it right.
Which Mr-Glass Models This Applies To
Mr-Glass fence systems fall into two broad families: the aluminum residential line and the heavier commercial-grade panels. Most Fort Worth homes in places like Wedgwood, Arlington Heights, and the Fairmount Historic District are running the residential aluminum series with pressed-glass infill panels. The identifying marks are on the underside of the top rail: you’ll see a stamped series code, usually a letter followed by three digits.
Before you order any part, measure the panel width from the inside of one post channel to the other. Fort Worth homes built in the 1990s and early 2000s commonly use a 6-foot panel, but we have measured everything from 4-foot side-yard panels to 8-foot driveway gates. The gotcha we see often: two neighbors will have fences that look identical from the curb, but one is the Mr-Glass residential line and the other is a lookalike from a big-box store. The aftermarket clone posts have a thinner channel wall, and Mr-Glass panel brackets will not seat correctly in them. We carry OEM Mr-Glass fence components on the truck for the most common Fort Worth series, along with quality aftermarket equivalents for discontinued lines. When a part is no longer manufactured, we will tell you plainly and show you the aftermarket option side by side before any work is ordered.
Styles & brands we work with
Signs Your Mr-Glass Fence Installation Is Failing
- Post lean at the base. North Texas clay soil expands and contracts through wet and dry seasons, and a post set in shallow concrete will start to tilt. Once the lean passes about 5 degrees off plumb, the panel brackets bind and the glass infill starts to rattle in its channels.
- Gate sag at the latch side. The hinge posts carry the entire gate weight, and on a double-drive gate that can be over 200 pounds. The first sign is a latch that misses its strike plate by a quarter inch, then by more as the post flexes.
- Frosted glass panel cracking at the corners. Fort Worth hail season runs hard from March through May, and a direct hit on a pressed-glass panel typically starts as a hairline crack at a corner clip. Left alone, it walks across the panel within one season.
- Rattling panels in wind. The rubber glazing gaskets inside the panel channels dry out in Texas sun after 7 to 10 years. The glass then floats loose in the frame and chatters every time the wind kicks up off the Trinity River corridor.
- White oxidation powder on aluminum rails. This is the clear anodized coating finally failing. It is not a structural problem by itself, but once the coating goes, the aluminum beneath starts to pit, especially within splash distance of sprinkler heads.
Replacement Cost & What’s Included
A full Mr-Glass fence installation in Fort Worth runs $3,500 to $9,000, with the spread driven by linear footage, gate count, post replacement, and whether we are reusing existing panels or installing new ones. A simple post replacement on an otherwise sound fence can come in well under that range. Here is how the pricing typically divides:
- Post replacement only (1-3 posts): $150 to $400 per post, including concrete removal and new footing.
- Panel replacement (residential aluminum with glass infill): $180 to $420 per panel, depending on width and series.
- Gate reset or rehang: $350 to $900 per gate, including hinge and latch adjustment.
- Full perimeter install (new panels and posts, 150-200 linear feet): $6,000 to $9,000.
Every quote is a written price before any work starts. No estimate that grows after the crew arrives, no change orders sprung on you mid-job. The final invoice should read the same as the written price – and if it doesn’t, we explain why before you sign anything. All our fence installation work carries the 365-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
There is a real safety line here, and we want you to know where it sits. A sagging gate hinge you can inspect and re-tighten yourself with a socket set, and you should. A leaning post is a different job. That post is buried in a concrete footing that weighs over 100 pounds, and pulling it out of North Texas clay with a car jack and a chain is how people end up in urgent care. Same with trying to remove a cracked glass panel while it is under tension in its channel: those panels shatter with zero warning and the shards are sharp enough to need stitches.
What you can safely do: check the post caps for water intrusion, tighten the bracket screws on the panels you can reach from the ground, and photograph the damage clearly before you call. What we do: remove and re-set posts with proper depth below the frost line (we go 24 to 30 inches in Fort Worth soil, which is deeper than most original installs), match the panel series correctly, and haul the old material away. If you are anywhere in Fort Worth and you are not sure whether the repair is safe to try, call (682) 708-9180 and describe what you are looking at. We will tell you straight whether it is a socket-set job or a crew job.
Key Takeaways
- Mr-Glass fence installation in Fort Worth runs $3,500 to $9,000 for a full perimeter job; individual post or panel repairs cost much less.
- We source OEM Mr-Glass fence components and quality aftermarket equivalents for discontinued series, and we identify which is which on the written estimate.
- Leaning posts and cracked glass panels are not DIY-safe jobs in our view. Tightening a gate hinge is.
- Written price before any work starts, shoe covers and drop cloths on every visit, and a 365-Day Done Right Promise on the completed installation.
FAQs
A properly installed aluminum Mr-Glass fence in Fort Worth should last 25 to 35 years before the posts need significant work, assuming the posts were set to at least 24 inches below grade and the drainage around each footing is decent. The glass panels themselves will outlast the hardware if they survive hail season unharmed. Call (682) 708-9180 if you want us to check the post depth and footing condition on an existing fence.
If the post itself is not cracked and only the footing has shifted, we can sometimes plumb the post and re-pack the base without a full replacement, but that repair is only as good as the original concrete. Once a post has cracked or the base has deteriorated into crumbly concrete, replacement is the honest fix. We will show you the post condition before we write the scope.
A single panel replacement on a matching series is usually a same-day job, once we have the part in hand. A full perimeter install with new posts runs three to five working days for a typical Fort Worth lot, and we schedule noisy work outside school pickup hours when families are still living in the house.
We stock the most common Mr-Glass residential panel sizes, post caps, and bracket kits on the truck for Fort Worth service calls. When we hit a discontinued series or an unusual panel width, we order the right part and bring it to your written estimate before the install date. Call (682) 708-9180 with your series code and we will check stock while you are on the phone.
Call Elmstead Remodeling Fort Worth for Your Mr-Glass Fence Installation
You will get a live person on the phone at (682) 708-9180, every time. We will ask about the series code on your fence, the panel width, and what the damage looks like, then we will schedule a free estimate with a written price before any work starts. Graham Stein grew up in Los Angeles, learned the trade at Los Angeles Trade-Technical College, and has spent decades doing construction and fence work across North Texas. He and his crew have worked on everything from quiet bungalows in the Fairmount Historic District to larger renovations closer to the Cultural District, and he writes every scope of work down before a single tool comes off the truck. The written price and the final invoice should read the same – if they don’t, that’s on us to explain before we hand you a pen.
Written by Graham Stein, Owner, Elmstead Remodeling Fort Worth at Elmstead Remodeling Fort Worth, serving Fort Worth and nearby areas.
