Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Fence Installation: The Fort Worth Owner’s Guide
Barrette fence installation in Fort Worth typically runs $3,500 to $9,000 for a complete perimeter job, and most partial replacements we handle fall in the $1,800 to $4,000 range depending on linear footage and the specific Barrette panel style you’re matching. We stock Barrette-compatible rail brackets, post caps, pickets, and gate hardware on our trucks, which means we can usually match your existing fence line the same week you call. The most common way homeowners discover a problem is quiet: a post starts leaning after a hard rain, or a gate drags against the concrete pad it cleared last spring. What looks like a single loose picket is often the first visible sign of a rail bracket that’s been corroding for two seasons.
If you’re reading this, you likely already know you have a Barrette product. What you may not know is that Barrette’s Fort Worth footprint is broad enough that matching the exact series matters more than most people expect. We’ll walk you through what to look for before you spend a dime.
Which Barrette Models This Applies To
Barrette Outdoor Living manufactures vinyl, aluminum, and composite fencing under several product lines, and the picket profile and rail channel dimensions vary between them. The Barrette DuraMax vinyl series uses a tongue-and-groove picket that slides into a U-channel rail, while their aluminum panels typically use a snap-in bracket system with a different post wall thickness. If you replace a DuraMax picket with a generic vinyl picket from a big-box store, the tongue profile won’t seat correctly, and you’ll get wind rattle within months. That’s a compatibility gotcha we see often in Fort Worth neighborhoods where original builders used Barrette products in the early 2000s.
To identify your exact model, check the inside face of the top rail near a corner post. Barrette stamps a series code there on most lines, and the picket width is your next clue: DuraMax pickets measure 6 inches wide on standard panels and 8 inches on the premium series. If the stamp is gone, measure the rail channel depth. Aftermarket pickets rarely match Barrette’s channel tolerance, which is why we pull OEM stock for Barrette jobs rather than generic equivalents unless the original part is discontinued. When OEM is no longer available, we have two Fort Worth supply houses we trust for aftermarket rails that maintain the same gauge, but we’ll tell you before we use one and explain the difference in writing.
Elmstead Remodeling Fort Worth is an independent contractor. We are not affiliated with Barrette Outdoor Living, but we stock their parts because so many Fort Worth homes were built with them, and we think matching the original product line is the right way to do the work.
Styles & brands we work with
Signs Your Barrette Fence Installation Is Failing
- Posts leaning at the gate or corners. Fort Worth’s clay soil expands and contracts through wet-dry cycles, and a post set in concrete less than 24 inches deep will slowly shift. We see this most on fences installed before 2010, when 18-inch post depths were common practice.
- Gate dragging or latching poorly. The hinge side of a Barrette gate carries more load than the panel itself, and the hinge screws pull through the vinyl frame over time. Once the screw holes wallow out, re-tightening them won’t fix it; the rail needs a reinforcement insert.
- Pickets popping out of the bottom rail. This is almost always a rail that has filled with silt and water, forcing the picket tongue up. Barrette rails have drain notches, but Fort Worth’s heavy spring storms overwhelm them if the rail was installed slightly out of level.
- White chalky residue on vinyl panels. That’s UV oxidation from a dozen Texas summers. The panel is still structurally sound, but the surface is degrading. It will not rinse off, and painting it without a vinyl-safe primer creates a bigger problem.
- Aluminum panels rattling in the wind. The snap-in brackets lose tension after years of thermal cycling. One loose bracket is a 20-minute fix. Twenty loose brackets usually means the bracket style has been revised, and retrofitting the new style is the more durable repair.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Barrette fence installation in Fort Worth ranges from $3,500 to $9,000, and the spread comes down to three things: linear footage, the Barrette series you’re matching, and whether you’re replacing posts or just panels and rails. A standard 150-foot backyard perimeter with DuraMax panels and new posts runs $5,200 to $6,800 on average. A smaller 60-foot side-yard section with the same product typically lands between $1,800 and $2,400.
Here’s how the numbers break down on a typical Barrette replacement job in Fort Worth:
- Parts (panels, rails, posts, caps, brackets): $1,400 to $3,800 depending on series and footage
- Labor including old fence removal and haul-off: $1,600 to $4,200
- Concrete for post setting: $90 to $300
- Gate hardware and re-hanging (if applicable): $150 to $500
Every Barrette installation we do in Fort Worth comes with a written price before the first tool comes off the truck, and that price includes shoe covers and drop cloths if we need to walk through the house to reach the yard. We photograph the clean-up before we leave, and the 365-Day Done Right Promise covers the completed installation. If a post shifts or a gate drags within a year of the job, we come back and make it right without arguing about whose fault it was.
DIY or Call Us?
You can safely check a few things before you call anyone. Look at whether your posts are plumb with a level, feel for loose brackets along the top rail, and check gate hinges for wallowed-out screw holes. These are diagnostic steps, not repairs, and they’ll help you talk through the problem on the phone.
What we don’t recommend is pulling posts yourself. An old post set in a deteriorating concrete footing can come out of the ground with surprising force, and a fence section under tension from a leaning post can shift suddenly when you loosen it. Most Barrette panel failures are also not single-part fixes: a popped picket usually means a clogged rail, and a clogged rail is a drainage problem that will repeat until the rail is re-leveled. That’s the kind of thing we’d rather catch on the first visit than have you chase part by part.
If you’d rather have a straight answer about what’s failing and what it costs, call Graham and the team at (682) 708-9180. We’ll come look, write down what we find, and hand you a price before anything gets touched.
FAQs
A properly installed Barrette vinyl or aluminum fence lasts 20 to 30 years in Fort Worth’s climate, with posts set at least 24 inches deep in concrete. Panels and rails hold up well; it’s the post footings, gate hardware, and drain channels that usually fail first, between years 10 and 15. If your fence is in that age range and showing symptoms, a partial replacement is often more cost-effective than chasing individual parts. Call (682) 708-9180 and we’ll tell you honestly whether you need a section or a full perimeter.
Yes, if the post footings are still solid and the rails haven’t filled with silt, a single section can usually be repaired for $300 to $900 in Fort Worth. The repair makes sense when the damage is isolated to one or two panels; if three or more sections are failing, replacement costs per linear foot drop enough that it’s the smarter spend. We’ll show you both numbers and let you decide.
Most Barrette fence replacements in Fort Worth take two to three working days from old fence removal to final gate adjustment, and we schedule a walkthrough on the last day. Concrete post footings need one full day to set before panels go on, so the timeline is rarely compressed below two days. Weather can extend it; we’ll tell you the schedule in writing before we start.
We stock Barrette-compatible rails, pickets, post caps, brackets, and gate hardware for the DuraMax and aluminum lines, and we can pull OEM parts for most other Barrette series within one to two days from our Fort Worth suppliers. If your specific part is discontinued, we’ll source the closest match and explain the difference before installing it. Call (682) 708-9180 with your series code or a photo of the damaged section, and we’ll tell you what we have before we schedule anything.
Written by Graham Stein, Owner, Elmstead Remodeling Fort Worth at Elmstead Remodeling Fort Worth, serving Fort Worth and nearby areas.
