Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Fence Installation: The Fort Worth Owner’s Guide
Boral fence installation in Fort Worth typically runs $3,500 to $9,000 for a complete perimeter job, and we stock Boral-compatible post inserts, rails, and trim on our trucks so most replacement work starts the same week you call. Most owners discover a problem the way you probably just did: a gate dragging, a post wobbling at the base, or a kickboard that has started pulling away from the rail after a few hard Texas summers of clay-soil movement. The good news is Boral components are modular, which means you rarely have to replace an entire fence line when one section fails.
We’re an independent Fort Worth contractor, not affiliated with Boral, but we have installed and repaired enough of their fencing to know exactly which parts hold up in our soil and which ones need a slightly different approach here than they would in, say, a sandy coastal lot.
Which Boral Models This Applies To
Boral manufactures fence components under a few distinct lines, and the compatibility rules are stricter than most homeowners expect. The finished pickets, rails, and post sleeves are engineered to specific dimensions: the standard picket is 6 feet tall and roughly 7 inches wide, and the routed bottom rail accepts those pickets at a specific depth. If you have a Boral fence that predates around 2018, the bottom rail profile changed slightly, and older pickets will not seat cleanly into the newer rail without modifying the tongue.
The fastest way to identify what you need is to pull one picket and look at the back face near the bottom edge. Newer Boral pickets have a small mold code stamped there, usually a two- or three-digit number. That code tells us which production run the board came from. For aftermarket equivalents, we have seen bargain rail inserts from generic suppliers that are a full eighth of an inch too narrow, which leaves the picket loose enough to rattle in north Texas wind. We default to genuine Boral components when they are available and tell you clearly when an aftermarket part will actually match the original tooling. The brands we trust for other material categories, like KraftMaid, Cambria, and Silestone, operate the same way: the name means a specific specification, and the substitution has to match the spec, not just the general idea.
Styles & brands we work with
Signs Your Boral Fence Installation Is Failing
- Pickets pulling free from the bottom rail. Boral’s system relies on a routed channel and a friction fit, and once the rail spreads even slightly, pickets start working loose. In Fort Worth, the freeze-thaw cycles in January and February are usually what starts this.
- Post sleeves loosening at the base plate. The post sleeve sits over a steel post anchored in the soil, and when our clay expands after spring rain, the sleeve can lift off its base. You will see a gap at ground level where grass debris collects.
- Gate sagging toward the latch side. Boral gates are heavy for their width because the material is 1.5 times denser than generic vinyl. A sagging gate usually means the steel post core has started leaning in the soil, not that the picket material failed.
- Hairline cracks radiating from screw holes. Texas heat makes the material expand, and if the original installer drove screws too close to the edge or without pilot holes, the expansion starts stress cracks that run outward over a couple of summers.
- Rattling during north wind. If you hear the fence talk back at you during the spring fronts, a rail connector or post channel has loosened enough that the system is rubbing instead of holding still.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Boral fence installation on a standard Fort Worth lot runs $3,500 to $9,000. A partial repair, like swapping out one section of failed rail and reinstalling pickets, sits at the lower end of that range or below it depending on how many posts are involved. The main cost drivers are total linear feet, how many steel post cores need to be reset versus reused, whether the existing pickets are in good enough shape to re-hang, and whether the old footing has to be dug out and repoured.
You get a written price before any work starts, and that price includes the parts at our cost plus a printed labor line, so you are not guessing what the material markup is. We write the scope down in plain language: how many posts, how many rails, what gets reused, and what the clean-up plan is. The written price and the final invoice should read the same, and if they do not, that is on us to explain before we hand you a pen. Every job also carries our 365-Day Done Right Promise, which applies to Boral fence work the same way it applies to a five-figure kitchen remodel.
DIY or Call Us?
Boral fence work is lower-risk than a lot of what we do, and there are a few things an owner can safely check before spending money. You can walk the line with a level to see which posts have drifted, look for gaps at the bottom of the post sleeves, and clear soil that has mounded against the kickboard, since trapped moisture is one of the main reasons Boral sections fail early in Fort Worth. You can also re-seat a single picket that has popped out of the rail, provided the rail channel has not spread.
Where we step in is when a post core has actually leaned or rusted, because resetting a steel post in north Texas clay is not a beginner task. Done wrong, you get the same lean back in eight months. We dig the footing, check the existing post core for rust, and re-anchor it at the same depth Boral’s system specifies. If you are not sure whether your issue is cosmetic or structural, call (682) 708-9180. We will walk through what you are seeing and tell you honestly whether it is a repair or a replacement before anyone schedules an estimate.
FAQs
A properly installed Boral fence in Fort Worth should last 20 to 25 years before the structural components need attention, though kickboards and bottom rails in low-lying yards might need service sooner because our clay holds water against the material. Call (682) 708-9180 and we can tell you what a failing section looks like before you spend money on a full replacement.
Yes, most Boral failures are repairable, especially if the problem is a spread rail, a lifted post sleeve, or a stuck gate hinge, because the system is built to be disassembled and reset. The exceptions are cracked post cores and rails that have been split by freeze damage, which usually need full section replacement.
A partial section repair usually takes a single day on site, and a full perimeter installation on a standard Fort Worth lot runs two to three days depending on how many post cores need fresh footings. We schedule noisy work outside of school-pickup hours whenever a family is home during the day.
We stock the most common Boral post inserts, bottom rails, and gate hardware on our trucks, and for less common components we can typically have them in hand within a week through our supplier network. If you send a photo of the failed part, we can often identify it before the first visit so the estimate call is shorter.
Call (682) 708-9180 to schedule your free Boral fence estimate in Fort Worth. We will put eyes on the fence, write the scope down, and hand you a price before any work is scheduled.
Written by Graham Stein, Owner, Elmstead Remodeling Fort Worth at Elmstead Remodeling Fort Worth, serving Fort Worth and nearby areas.
