Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cover Kitchen Remodeling: The Fort Worth Owner’s Guide
If you own a Cover kitchen and the remodeling work is starting to show its age in Fort Worth, the typical installed price for a kitchen remodel runs $14,000 – $45,000 depending on cabinet layout, countertop material, and whether we’re replacing or refinishing surfaces. Most families reach out after noticing drawer slides that catch, a faucet that drips at the base, or cabinet faces that have swollen from years of North Texas humidity cycling. We carry and install Cover-compatible kitchen components, and we give you a written price before any tool comes off the truck.
Elmstead Remodeling Fort Worth is an independent remodeling contractor, not affiliated with Cover. That independence matters: when a Cover kitchen component fails, we recommend the fix that serves your family, not a corporate replacement policy. Graham Stein has walked enough Fort Worth kitchens to know that a failed drawer glide in a Fairmount bungalow gets fixed differently than a cracked island countertop in a Cultural District renovation, and we write both scopes down the same way: line by line, before work starts.
Which Cover Models This Applies To
Cover kitchens vary more by installation year than by model name, and that single fact is what trips up most owners trying to source parts themselves. The cabinet hardware, hinge spacing, and countertop substrate changed several times across Cover’s production runs. A 2015-era Cover kitchen often used 35mm cup hinges with a 1/2-inch overlay, while later runs moved to a 3/4-inch overlay with soft-close dampers built into the hinge cup. Buying the wrong overlay means a door that won’t sit flush, no matter how carefully it’s hung.
Here’s the compatibility gotcha we tell every Fort Worth homeowner: before ordering any Cover replacement part, open one cabinet door and measure the distance from the hinge cup center to the door edge. Then check the drawer slide length with the drawer fully extended, not from the face. Cover used a mix of 18-inch and 21-inch slides depending on cabinet depth, and the slide length is stamped on the side of most slides. If yours isn’t marked, set a tape measure on the exposed slide and we’ll match it from what’s on our truck.
For cabinets, we install KraftMaid and Wellborn as direct replacements and upgrades when a Cover box is beyond repair. For countertops, Cambria and Silestone match or exceed the original Cover surface in both wear and warranty. OEM Cover parts are fine when they’re still available; we’re honest when a quality aftermarket equivalent will outlast the original at a better price.
Styles & brands we work with
Signs Your Cover Kitchen Remodeling Is Failing
- Drawer slides that catch, grind, or won’t stay closed. Fort Worth’s clay soil shifts houses subtly over time, and that movement takes a toll on cabinet alignment. The slide rollers wear unevenly, and what felt like a minor catch becomes a drawer that jumps the track entirely.
- Cabinet faces that have swollen, peeled, or discolored at the bottom edges. This is the classic North Texas humidity signature. Dishwasher steam, sink splash, and the region’s wet-dry cycles lift laminate and delaminate the substrate underneath.
- A countertop seam that has widened or a Silestone or Cambria surface that’s chipped at the edge. Seam failure shows as a dark line you can catch with a fingernail. Chips happen when a heavy pot lands wrong or the substrate underneath flexed during foundation settling.
- Faucet or fixture drips at the base or the handle. Hard water in the Fort Worth supply shortens cartridge life. A slow drip at the base means the O-ring or cartridge has worn; left alone, it works water under the countertop and into the cabinet below.
- Hinges that sag so the door rubs or won’t close square. Once a hinge screw strips out of a cabinet box, the door’s weight works against the remaining screws. We rebuild the hinge bore with a proper wood plug rather than filling it with toothpicks and glue, which we’ve seen fail again within a year.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Fort Worth, a full Cover kitchen remodel typically lands between $14,000 and $45,000. The spread comes down to scope: refinishing cabinet faces and replacing hardware sits at the lower end, while new KraftMaid or Wellborn cabinets, a Cambria or Silestone countertop, and a relocated island run toward the top. Every number includes the written price you’ll sign before we start, and that price doesn’t move once we’re on site.
Here’s how the common pieces break down:
- Cabinet installation: $4,000 – $13,000
- Countertop installation: $2,000 – $6,500
- Backsplash installation: $800 – $2,500
- Kitchen island installation: $3,000 – $10,000
- Small kitchen remodel: $9,000 – $20,000
Every Elmstead remodel includes shoe covers and drop cloths at the door, quiet tools during nap and school hours where we can, and a photo of the clean-up before our crew leaves each day. We use pet-safe products where there’s a choice available, and we ask before touching or moving anything that belongs to your family. The 365-Day Done Right Promise stands behind every job: if it’s not done right, we make it right.
DIY or Call Us?
A homeowner in Fort Worth can safely handle a few checks: tightening a loose hinge screw, cleaning slide rollers with a dry cloth, and noting where the swelling or wear is worst so you can describe it accurately on the phone. Those observations save time and help us bring the right parts on the first trip.
What goes wrong in a DIY Cover repair is alignment and substrate. A cabinet box that’s out of square by even an eighth of an inch will wear out new slides within months. A countertop seam that’s improperly leveled telegraphs through the stone. And faucet work above a countertop means working in a tight space with water connections that have hardened over Texas summers. None of this is high-tension or electrical danger, but it’s the kind of work where a small mistake turns a $2,000 fix into a $8,000 one. Call (682) 708-9180 and we’ll give you a written estimate before anything is touched.
FAQs
Most Cover kitchen components last 10 – 15 years in Fort Worth’s humidity and shifting soil, though drawer slides and faucet cartridges often need attention at the 7 – 10 year mark. Countertops from Cambria or Silestone carry warranties that travel with the finished project. Call (682) 708-9180 and we’ll tell you honestly whether your kitchen needs a repair or a replacement.
Yes, in many cases. Stripped hinge bores, worn slides, delaminated cabinet doors, and chipped countertop edges can often be repaired without replacing the entire run. We’ll give you a written price for the repair before we start, and we won’t push a full replacement when a repair will hold.
A partial Cover kitchen repair usually takes one to two days. A full kitchen remodel runs two to six weeks depending on cabinet lead times and countertop fabrication. We’ll give you a schedule in writing with the estimate, and we respect your family’s quiet hours throughout.
We carry common hinge styles, drawer slides, cartridges for Kohler and Moen fixtures, and cabinet repair materials on the truck in Fort Worth. If your Cover part needs to be ordered, we’ll tell you the lead time before you commit to anything. Call (682) 708-9180 for a free estimate and a written price.
Written by Graham Stein, Owner, Elmstead Remodeling Fort Worth at Elmstead Remodeling Fort Worth, serving Fort Worth and nearby areas.
